Small Diamond Core Drills
|1 - 4||$7.66|
|5 - 9||$6.84|
|10 - 24||$5.43|
Sizes Available: 1.00mm, 1.50mm, 2.00mm, 2.50mm, 3.00mm
***New 3mm Design***
Similar to our small diamond drill bits but with a core running through the middle, these diamond core drill bits are hollow allowing water to circulate inside the core. Ideal for beginners and great for drilling holes in glass, sea glass, tile, ceramic, glazed pottery, beach pottery, beads, pebbles, slate, petrified wood, optical material, composites and rock.
Not suitable for very hard glass, stone, porcelain, shell, fossilized bone or hard precious or semi-precious stones such as quartz - please use our small diamond drill bits instead.
Helpful Note: 3mm diameter has a clearance side hole, all other sizes do not.
- Use on slow speeds. We recommend 5,000-10,000 rpm
- Use little pressure. Let the weight of your rotary tool do the work
- Use with plenty of cold water
Please read on for usage instructions, chuck and collet requirements and further information...
Small Diamond Core Drills Versus Small Diamond Drill Bits
Small Diamond core drills will glide through material a little easier and more quickly than the solid ended small diamond drill bits making them the ideal choice for beginners.
However, the small diamond coring drills have a smaller surface area of diamond grit and have a core running through them which makes them slightly less robust and not quite as durable as the small diamond drill bits.
Users often keep a combination of both types in their tool kit, or you may find a personal preference to using one over the other.
How to use Diamond Drill Bits:
You will need an adjustable chuck or collet to hold these small diamond core drills, take a look under the 'Technical' tab below to find out the shank sizes of these drill bits.
If you have a Dremel rotary tool, we recommend the Dremel Multi Chuck. This allows you to change drill bit sizes easily.
Tip: The following three crucial elements when drilling will prevent the diamond grit wearing off or burning away, will prevent the drill bit from snapping (too much pressure applied), prevent your material from cracking, and extend the life of your drill bits.
- Use with plenty of cold water (if drilling in a container, change the water when it turns cloudy)
- Use on a slow speed of 5,000RPM
- Use at low pressure, let the drill do the work
In order to get the best from our diamond tipped drill bits, please ensure you read through the Tutorials section on our blog before attempting to use our drills for the first time. Here you will find tips and video footage on how to drill glass, how to drill gemstones, how to drill bottles, how to drill pebbles and how to drill sea glass. There are also helpful hints on the correct speeds and pressure to be used.
You might also like to read our article: 12 Things you Should Know about Diamond Drill Bits
What is a Core Drill?
Our diamond core drills are designed to drill holes in very hard materials and they do this by removing a cylinder of the material.
The core allows drilling with water or a lubricant to swirl up inside the core whilst drilling, preventing overheating. Overheating can cause your material to crack or break and will shorten the life of the drill bit.
Many of our customers use our core drill bits to achieve a core rather than to drill a hole. We can't guarantee the precision with which you might achieve the perfect core but many have done so with success.
From time to time the debris may become stuck in the core of the drill bit. If this happens it will often become dislodged when you begin drilling your next hole. Alternatively use a wire brush to clean out the core of the drill bit. To prevent this from happening, drill in and out (up and down) as you drill to dislodge the debris. This will prevent the debris from being pushed up the core of the drill bit.
If you are new to these diamond drill bits then our Infographic 'How to Drill Through Glass' has easy to follow steps.
Disclaimer. Using rotary tools near water has never been, to the best of our knowledge, endorsed by any of the rotary tool manufacturers. If you do choose to drill near water or with attachments under water connected to your drill then you do so at your own risk. Please be aware that mixing electricity and water can be very dangerous.
Diamond grit 120# is precisely electroplated onto a hardened steel shank
- Overall length: 60mm
- Diamond working length: 3.0mm - 5.0mm
- Shank: 0.75mm
- Tolerance +/-0.1mm
- Overall length: 65mm
- Diamond working length: 6.0mm - 8.0mm
- Shank: 1.48mm
- Overall length: 65mm
- Diamond working length: 4.0mm - 6.0mm
- Shank: 1.50mm
- Overall length: 65mm
- Diamond working length: 5.0-6.0mmmm
- Shank: 2.0mm
3.00mm Diameter (with clearance side hole)
- Overall length: 50mm
- Diamond working length: 4.0mm
- Shank: 2.70mm
- Tolerance +0.1mm
Questions & Answers
Ask a question using the form below
Other questions and our answers
Can these bits (small diamond core drills) be used with a Dremel rotary tool? Thank you in advance. Best regards, Silvio Berra
Thanks for your enquiry. Yes the small diamond core drills bits are ideal to use in a Dremel rotary tool, but you will need the Dremel Multi Chuck to hold the very small shanks of these drill bits.
I want to order diamond bits to drill 1mm holes in 500um thick borosilicate glass wafer. Could you please tell me if 0.75mm diameter drill bit would be perfect for that or not. Also, what other items I would need to drill hole along with drilling machine. Besides, could you suggest me which drilling machine would be sufficient for this job.
Good to hear from you. We recommend using a Dremel 3000 drill with a Dremel Multi Chuck and use either the small diamond drill bits or the small diamond core drills. If you are new to drilling holes in glass we recommend trying the core drills first. The size of the core drill indicates the size of the hole you will achieve, so if you need a 1mm hole, you will need to purchase the 1mm diamond core drills. All the best with the project.
Will the small diamond drill bits work in a drill press ?
Hello Ann, Yes they work perfectly well in a drill press. They will work in any drill so long as there is an adjustable chuck to hold the shank of the drill bits.
Will your drill bits fit my drill?
Our drill bits will fit all rotary drills so long as you have an adjustable collet or chuck with which to hold the shank of our very small drill bits. Sometimes when buying a drill they will come with an adjustable collet but if you find you are in need of one then we supply either a Dremel Multi Chuck (DMC4486) or a Dremel Collet Nut Kit (DCNK4485).